I’ve sent out the PCB order for my RGB stick!
I’ve put up a page on the right-hand side with detailed information and pricing for them. They’ll be available in approximately two to three weeks. Initially I only have a limited supply of parts for them, so please comment on the RGB stick page saying if you’re interested in them. This will help me decide how many LED’s to buy.
What would actually be useful product for people? I thought I’d jump onto the Arduino bandwagon and convert my triple 700mA LED driver into an Arduino shield, perfect for driving Luxeon Rebel LED’s and other high power LED’s. I had some extra space on the PCB, so I decided to squeeze in an ATTiny and let it do PWM dimming controlled by I2C. So you can stack a bunch of these shields and let them do all the work.
Of course, this adds quite a bit of BoM cost to the board (the entire bottom part of the board below), but it’s entirely optional. If you just want to drive one RGB LED, then there will be a cheaper version without the onboard microcontroller and associated circuitry populated. The PWM inputs are connected to Arduino pins 9-11, which can do hardware PWM. Here’s a preview while the board’s being manufactured…
Jumper to select between using VIN from the Arduino board or external power jack/terminal block.
More details, schematics, etc, will come shortly. I will publish details on customization for those of you who want to play around with these drivers.
Intended price point: under $50 for sure! Sparkfun must be making a killing off their board…
But what should I call it? RGBHBLEDuino doesn’t exactly roll off the tongue…
Also check out my other RGB LED project, the RGB stick
My board for the RGB HBLED driver using the HV9918 from Iteadstudio came in. I’m pretty pleased with the quality for the price (10 for $28 + shipping). Turnaround time was about two weeks.
Hopefully it’ll work once I populate it. I was testing the HV9918 on a protoboard but the chip kept dying on me inexplicably. We’ll see in the next update.
While waiting for my high brightness LED boards to come, I finally finished up the TLC5947-based board, which I ordered from Sparkfun’s BatchPCB service. I had made the LED holes too small so I had to surface mount solder each LED individually, which took forever.
It uses one TLC5947 per 24 channels, which does 12-bit PWM on each individual channel. All the MCU has to do is shift in 12 bits per channel, and send a latch signal. The PWM clock signal is generated by the TLC5947′s, which makes it a lot easier to use than the TLC5940′s. They can also be chained together. Here’s a video of it in action:
At full brightness it’ll draw about 2A of current. The TLC5947′s get pretty toasty when running them at 5V, but they work just fine at 4V and dissipate much less power.
I need to think of something cooler to display than just a cycling rainbow…
The HV9918 board design’s done! It’s a lot more cluttered than Sparkfun’s board but a lot of the components are optional. When the boards come I’ll determine if input caps for each driver are actually needed. Hopefully it’ll be good enough to drive the Luxeon Rebels I bought.
It was a quick design to test out the chips before finalizing. The boards only cost $28 + $3 shipping to make from iTead Studio. And I get ten of them:
http://iteadstudio.com/store/index.php?main_page=index&cPath=19_20
Way cheaper than the American PCB prototyping companies.
I bought a few of these high brightness RGB LED’s from my favorite sketchy site, DealExtreme:
They’ll probably arrive in a few weeks or so. But in the meantime, how do you drive these 350mA LED’s? Sparkfun sells one:
However, they’re almost $50! That’s pretty expensive, considering the LEDs themselves only cost at most $20. DealExtreme sells inexpensive LED drivers but it’s awkward having to use three boards to dim each channel individually. So, I’ve decided to learn about DC/DC converters and make my own driver board. I decided to make it as flexible as possible: be able to drive LED’s in series up to 20V with a wide input range and deliver 700mA. Also, if I could make them low cost then I could potentially sell them too. I considered several driver IC chips and iterated through a design for each of them:
Since I basically have no experience with DC/DC converters, I decided to spend a weekend trying to simulate my design as much as possible. But there aren’t any SPICE models for any of these chips, and the design guide was especially sparse for the chip I decided to use in the end, the HV9918. So, I attempted to model the device myself, based on their block diagram and chip specs. I think I was mostly successful:
Blue shows the inductor current, and green shows the LED current. The 0.47uF output capacitor across the LED’s reduces the ripple by quite a lot, from 300mA to 30mA.
The HV9918 offers dimming from both a digital input and also an analog 0-2V input, which is great for relieving the microcontroller from doing the dimming. However, the dimming is highly non-linear below 0.1% duty cycle, as the inductor has to charge up, and the output capacitor has to discharge, so it is not possible to dim smoothly at very low light levels. Also, since this chip uses a high-side current sense, it is difficult to add an op-amp to alter the sense voltage as I had originally planned with the other chips.
When the parts finally come, I’ll see how well my model matches up with the chip itself. I’ll also be testing them at 700mA driving some Luxeon Rebel LED’s.
I’ll be designing my board for the Sparkfun driver mechanical layout so that it is compatible with their LED board/heatsink solution. If there’s demand for them, I’ll try to sell them. My intended price points are $20 for the three-driver version and $10 for the single driver version.
Recent Comments